British Twin-Motor Electric Paramotor

Jack Faust, a hang-glider pioneer, recently informed your editor of this British back-pack flying pioneer. 

Tony Canderton of Electric Paramotor UK has created a twin-motored parachute that uses stock aluminum extrusions and model aircraft components to take him flying.

Tony Canderton flying his twin-motor creation

As noted on his web site, “Most of the parts used are pretty easy to come by, taken from giant scale RC and the frame is aluminum.   No welding was used – just nylon lock nuts and bolts.  The whole unit weighs in at just over 19 kilos (41.8 pounds) with batteries and harness and puts out 27 kilos (59.4 pounds) of static thrust.”

Motors are EMP model XYH80-100-As, each capable of producing a peak 6,500 Watts (8.7 horsepower) from a 1.75 kilogram (3.85 pounds) unit.  These have a 12 millimeter (1/2-inch) shaft, a bit more substantial than some model motors and aiding their purpose in turning direct drive propellers.   EMPs seem to be available in England only, but cost a mere 85 pounds each (about $136) – real economy champs.  Canderton notes the motor is similar to Turnigy model aircraft units which are available in the U. S.  A Turnigy Rotomax 100cc motor is about $375, and is roughly equivalent in output to the EMPs.

A word of caution here.  Many of these model aircraft motors, especially those made overseas, are not the equivalent of American-made motors such as those from Steve Neu and AstroFlight Products, Bob Bouchard’s operation in California, or German products such as those from Plettenberg and Hacker.  These seem to have better reported reliability at a higher price (some not that much greater).  Users must determine how much they value their physical well-being before committing to any power system.

 

Simple, well-made frame uses model aircraft motors, controller and battery packs

Canderton uses four 5,500 milliAmp-hour battery packs arranged with four cells in parallel and six in series (4P/6S) to gain the necessary voltage and amperage.  He then connects two of these packs in series to feed 44.4 volts to each motor.  While charging or using these packs on this backpack frame, Canderton takes the precaution of enclosing them in a “Lipo-sack,” a thermal insulation sleeve that protects users from thermal runaways in the cells.  These should give around a half-hour run time with motors at full power.

Current is fed through two Hobbywing Platinum 120A HV OPO ESCs (electronic speed controllers).  These can handle 120 Amps continuously, and are optically isolated, using fiber optic, rather than electric signals, to modulate the controller’s output.

Controllers are “throttled” though a servo tester, used by model airplane flyers to check operation of devices that make ailerons and tail feathers wiggle in proper fashion.

As can be seen, such a rig can be devised for reasonable amounts of money, and if one already has a canopy, can be a fairly immediate source of aerial gratification.  This type of rig could be adapted to nano-trikes and with modification, find its way onto the trailing edges of ultralight sailplane wings.

Experimenters like Tony Canderton show the many ways in which we can find ourselves in the skies affordably.  He invites reader input, a profitable enterprise for him and our readers.  (Addition, June 24: Tony says this is meant to be a “People’s EPPG. and the best way to assure that is through the Internet.”)

{ 4 comments… add one }

  • Mark e. 06/28/2012, 6:06 pm

    Just a word of caution about your word of caution. Powered paragliders are gliders, it is in the name and an engine or in this case motor out should be a non event. If a power failure becomes an emergency the pilot has severely “screwed the pooch”.

    (Editor’s Note: CAFE does not approve of animal cruelty, but does acknowledge that motor failure in a paraglider would probably be the most benign of catastrophes.)

  • Terry M. Palmieri 06/29/2012, 8:40 am

    I am very impressed with the time, effort and cost invested in this unit. It looks like a quality product from start to finish. I would love to see a schematic of the electrical components and some more photos. Keep up the great work and fly safe.

  • arun srinivas 02/10/2013, 6:35 am

    How much gap is there between the propellers is there a possibility of collision.

  • Nick Simmons 03/05/2013, 2:36 pm

    If Jack Faust wishes to take things any further please ask him to email me as I will be able to help with any of the fabrication stuff required. I have a TIG welder in my workshop in Swindon Wiltshire and used to be an Aircraft Welder and Sheet Metal Worker in the Royal Air Force. I was licensed to weld Rolls Royce jet engine components. I am able to weld Ali, Stainless and Titanium together with others. Maybe I could help with any airframe aspects he feels he wants to over come. I hold a BHPA Pilot rating for foot and tow launch operations and have been towed in the Netherlands too. Kind Regards Nick Simmons

Leave a Comment